NZ-WIDE SHIPPING - FREIGHT FREE
cart Shopping Cart Shopping Cart
NZ’s Widest Range Of Industrial Adhesives
 
Premium Quality Guaranteed
 
Bulk & Wholesale
Prices
 

QLC440

QLC440

Quilosa Leveling Compound - 40mm, 25kg

Quilosa Leveling Compound - 40mm, 25kg
larger imageMove mouse over the image to magnify
Cement based self-leveling compound.
NZ$49.00
excl GST
Qty.
QUILOSA LC-440 is a cement based self-leveling compound for filling, smoothing and leveling surfaces prior to installation of flexible coatings, parquet or ceramic, indoor or outdoor.

COMMON USES

It can be used for radiant floors without additives needing to be added.
Suitable for leveling, in layers from 3 to 40 mm, floors of concrete, cement, anhydrite, ceramic or others. Thicknesses up to 60 mm can be obtained adding aggregates.
QUILOSA LC-440 is characterized by a very low shrinkage.
It can be used for underfloor heating.

PREPARATION

The floor must be consistent, smooth and firm and free from dust and grease.
Any remains of paint or glue on the surface must be removed mechanically as far as is possible.
Old ceramic floors must be energetically cleaned and sanded with an abrasive.
This product is not a vapour barrier and is permeable to moisture. Follow the coating instructions regarding the maximum moisture content and verify the surface before installing QUILOSA LC-440. If surface moisture exceeds 75% (measured with a calibrated hygrometer) or 2% CM / CM method), install an anti moisture membrane.
Before applying the leveling compound QUILOSA LC-440, you may like to apply a primer on the surface: Thomsit R766.

APPLICATION

Pour 4.5 litres of water into a container for every sack of 25 kg of product. Mix until a fluid and homogeneous paste is obtained. Using a mechanical stirrer at 600 rpm is recommended.
Leave the mixture for 3 minutes and mix it again for the paste to be ready to use.
Pour the mixture onto the floor and spread it with a levelling bar until the recommended thickness is obtained.
Surfaces may be more easily equalled using a level. For very thick surfaces, using a spiked roller is recommended.
Do not mix a larger amount than can be applied in 25 - 30 minutes.

TECHNICAL FEATURES

Working time: Approximately 40 minutes at 20ºC
Time before treading: 4 hours approximately
Time before gluing coverings: 24 hours for thicknesses up to 10 mm.
Working temperature:> 5ºC
Yield: Approximately 1.7 kg/m2.mm
Compression strength: Approx. 25 N/mm2 at 28 days.

STORAGE

18 months in its original hermetically sealed containers at temperatures of between 5 and 25ºC.

CLEANING

Tools may be cleaned simply with tepid water before the product has completely set.

HEALTH & SAFETY

QUILOSA LC-440 contains cement. Mixing with water produces a strongly alkaline reaction. Protect the eyes and skin. In case of contact, wash immediately with abundant water. In case of contact with the eyes, seek medical attention.


TECHNICAL DATA SHEET Download

You might also be interested in ...

QUILOSA BH-210 MS Flooring Adhesive 15kg
NZ$230.80
excl GST
QUILOSA Orbafoam Cleaner 500ml
NZ$21.40
excl GST
QUILOSA CA Accelerator 150ml
NZ$17.30
excl GST
Quilosa Leveling Compound - 10mm 25kg
NZ$39.00
excl GST

CUSTOMER SERVICE

Contact Us
Trade Accounts
Terms of Trade

 


 

 

Ph: +64 9 444 4878
Fax:

Email:

Shop:
+64 9 442 5972

enquiries@glueguru.co.nz

18 Kaimahi Road
Wairau Valley
Auckland 0627